Focus on environmental protection and devote to pollution prevention

Provide reliable and safe product for
the electronic industries

Technical support

6-7 Operation Manual for Flux
6-7-1 Preparation:

1. Circuit boards and components: In order to maintain a stable welding performance and electrical reliability, circuit boards and components shall meet the solder-ability requirements and ion pollution requirements. Assembly manufacturers are suggested to establish the relevant provisions based on the requirements mentioned above and suppliers may be required to provide analysis reports or incoming inspection.
2. Pick-and-place: It is recommended that wearing clean non-woven gloves when picking or placing circuit boards. Please be cautious when contact the circuit boards; only the edge can be touched.
3. Cleaning: Conveyor belt, fixtures and trays should be kept clean and can be cleaned with detergent. In the replacement of a flux, it is recommended to use the new foam tubes (have a clean-off).

6-7-2 Application:

1. For the foam, the foam compressed air devices should be free of water and oil, and maintain full flux, which should be maintained 2 ~ 3cm higher than the foam pipe. Adjust the air pressure to get the best foaming height and foam fineness, and to make it foam at a constant rate to the top.
2. For the spray, the uniformity can be estimated with a piece of board (cardboard, glass, etc.) through the spray and preheat areas.
3. Solid content control: When used in foam, the diluent should be added to supplement the volatile solvents, to control the flux of the solid content. In continuous production, check whether proportion of solid content is in acceptable range every 2-4 hours.
4. Residues and contaminants will accumulate in the repeated use of the flux in long term use. In order to obtain good welding results, replacing
flux every one or two days is recommended, as well as cleaning the diluent tank and foam tubes.
5. The removal of residues: residue remains after soldering; it can be cleaned with special detergent if necessary.

6-7-3 Equipment setting:

Operating parameters

Reference value

Coating volume

foam:1000-1800 ug/cm2
spray:800-1500 ug/cm2

used in foam

Foam aperture


Foam tube from the top to the surface flux


Foam pipe cover openings


Preheating temperature

Board surface


Plate under the surface


On-board increase in maximum speed of the surface (the original device in order to avoid injury)

2℃/3.5° F/s

Angle conveyors

5-8° (6°)

Conveyor speed


Tin furnace slurry contact time


Tin furnace temperature





Note: These are general guidelines and can lead to a good welding performance. However, different equipment, components and circuit boards will require different optimized settings, which require the pilot trials to determine the most important parameters (such as the volume of coating, conveyor speed, tin furnace temperature, preheating temperature).

6-7-4 Cautions:
1.In filtration and the welding process, avoid direct contact with skin and inhalation of steam. Better wear protective glasses and rubber gloves, masks in operation. If the any object splashes into the eyes in the process, wash the eyes immediately with plenty of water and seek for medical treatment afterwards.
2.Fetch the corresponding dose of flux according to the amount of output. Cap the flux liquid container if it’s not being used to protect it for future use; The color of flux may darken after long-time storage, which has no side effect for use.
3.Keep good ventilation in workshop or at the operation scene.
4.Operation must not be performed in haste. Be cautious in leaching flux and soldering process, in order to avoid flux  splashing or hot liquid spattering.

6-7-5 Fire Contral Related Parameters

Flash Point(°F):65 Auto Ignition Temperature:460℃
Uel Upper(VOL):7.99 Usual Fire Explosion Hazards:N/O
Lel loower(VOL):2.02 Extinguisher Media:CO2/Powder Extinguisher
津ICP備05011517號-1 Copyright © 2010 Cooper ZhongyaSolder,Inc All Rights
四川快乐12走势图 买体彩七位数的技巧 黑龙江快乐十分前三组遗漏 股票配资客户开发流程 吉林快三玩法两不同 辽宁35选7中奖规则 31选7开奖结果走势图 今天快三开奖江西 福建漳州股票配资公司 pc蛋蛋真送q币 广东11选5人工计划全天计划 贵州快三今天开奖结果查询 pk10在线精准人工计划 幸运赛车技巧 福建快3第49 茅台股票代码是多少 钉钉天天红包赛能获得多少钱